Calificación:
  • 2 voto(s) - 5 Media
  • 1
  • 2
  • 3
  • 4
  • 5
Engine Rebuilds
#1
Our Core business as well as making some Rx8 specific products is engine rebuilding and we currently offer this in 4 standard packages, 

1. Standard Plus Rebuild service
2. Street Port Rebuild 
3. Half Bridge Rebuild 
4. Full Bridge Rebuild

We can provide the engine block if necessary and will come ready to install complete with injectors, wiring harness and lower intake manifold. The price of us providing the block is £400

1. Standard Plus Rebuild service

The Standard Plus rebuild service will restore your engine to how it felt when it left the factory. This is benchmark standard that we adhere to.
 
Parts replaced as standard with this build are:
 6 x OEM Apex Seals
12 x OEM Apex Springs
12 x OEM Sideseals
12 x OEM Sideseal Springs
12 x Two Piece OEM Corner Seals
12 x OEM Corner Springs
12 x Rotor Inner, Outer, Scrapper Springs
2 x OEM Needle bearings
1 X Pilot Bearing
2 X OEM Stationary Bearings
2 X Bearing Retaining Screws
2 X OEM Rotor Bearings
All water, oil seals and gaskets will be replaced!

£1600 Plus shipping 

2. Street Port Rebuild 

The Street Ported Engine Rebuild has its inlet and exhaust ports enlarged to increase the breathing capabilities of the Renesis engine and therefore increases the power of the engine. A worthy investment other the Standard Plus package and considered the bang for buck modification for those seeking a little more power from the Rx8.

Parts replaced are the same as the standard package 

£1850

3. Half Bridge Rebuild 

The Half Bridge Engine Rebuild has its inlet and exhaust ports enlarged to increase the breathing capabilities of the Renesis engine just like the Street Port but in addition to this the Auxiliary Ports are bridged which means further power increases over the street port but still retaining all the driving characteristics of the Street Port.  There are significant power gains over stock with this type of porting and helps the Renesis pull hard all the way to the red line.

Parts replaced are as standard package plus a higher pressure oil regulator at 95 PSI 

**This must be built with Goopy Apex seals which adds a little cost.

£2050 Plus shipping 

4. Full Bridge Rebuild

The Full Bridge Engine Rebuild has its inlet and exhaust ports enlarged to increase the breathing capabilities of the Renesis engine just like the Street Port but in addition to this all inlet Ports are bridged which means further power increases over the Street Port. This is an aggressive port which will substantially increase the power of your Rx8.  To get the best from this rebuild a full mapping session is highly recommended once the engine is fully run in.

**This must be built with Goopy Apex seals which adds a little cost.

we can enhance ANY package to your requirements for instance if you require Goopy Apex seals or a higher oil pressure regulator this can be accommodated, please get in touch with your needs.

£2200 Plus Shipping 

Other Options:

Spark Plugs 
Engine Painting 
Refurbished housings 
Engine balancing 
Rotor lightening 
Lightweight Flywheels 
Clutches


Archivos adjuntos Miniatura(s)
       
Please Like and follow us on Facebook. http://www.facebook.com/ryanrotaryperformance

Website: http://www.RyanRotaryPerformance.com
Email: Sales@RyanRotaryPerformance.com
Contact: Carl Ryan 

Responder
#2
(16-08-2017, 08:47 PM)Ryan Rotary Performance escribió: Our Core business as well as making some Rx8 specific products is engine rebuilding and we currently offer this in 4 standard packages, 

1. Standard Plus Rebuild service
2. Street Port Rebuild 
3. Half Bridge Rebuild 
4. Full Bridge Rebuild

We can provide the engine block if necessary and will come ready to install complete with injectors, wiring harness and lower intake manifold. The price of us providing the block is £400

1. Standard Plus Rebuild service

The Standard Plus rebuild service will restore your engine to how it felt when it left the factory. This is benchmark standard that we adhere to.
 
Parts replaced as standard with this build are:
 6 x OEM Apex Seals
12 x OEM Apex Springs
12 x OEM Sideseals
12 x OEM Sideseal Springs
12 x Two Piece OEM Corner Seals
12 x OEM Corner Springs
12 x Rotor Inner, Outer, Scrapper Springs
2 x OEM Needle bearings
1 X Pilot Bearing
2 X OEM Stationary Bearings
2 X Bearing Retaining Screws
2 X OEM Rotor Bearings
All water, oil seals and gaskets will be replaced!

£1600 Plus shipping 

2. Street Port Rebuild 

The Street Ported Engine Rebuild has its inlet and exhaust ports enlarged to increase the breathing capabilities of the Renesis engine and therefore increases the power of the engine. A worthy investment other the Standard Plus package and considered the bang for buck modification for those seeking a little more power from the Rx8.

Parts replaced are the same as the standard package 

£1850

3. Half Bridge Rebuild 

The Half Bridge Engine Rebuild has its inlet and exhaust ports enlarged to increase the breathing capabilities of the Renesis engine just like the Street Port but in addition to this the Auxiliary Ports are bridged which means further power increases over the street port but still retaining all the driving characteristics of the Street Port.  There are significant power gains over stock with this type of porting and helps the Renesis pull hard all the way to the red line.

Parts replaced are as standard package plus a higher pressure oil regulator at 95 PSI 

**This must be built with Goopy Apex seals which adds a little cost.

£2050 Plus shipping 

4. Full Bridge Rebuild

The Full Bridge Engine Rebuild has its inlet and exhaust ports enlarged to increase the breathing capabilities of the Renesis engine just like the Street Port but in addition to this all inlet Ports are bridged which means further power increases over the Street Port. This is an aggressive port which will substantially increase the power of your Rx8.  To get the best from this rebuild a full mapping session is highly recommended once the engine is fully run in.

**This must be built with Goopy Apex seals which adds a little cost.

we can enhance ANY package to your requirements for instance if you require Goopy Apex seals or a higher oil pressure regulator this can be accommodated, please get in touch with your needs.

£2200 Plus Shipping 

Other Options:

Spark Plugs 
Engine Painting 
Refurbished housings 
Engine balancing 
Rotor lightening 
Lightweight Flywheels 
Clutches

Hi!

Could you put the prices of the options? And also the price of the goopy apex seal for ported engine?

Thanks!
Responder
#3
(18-08-2017, 09:56 AM)naj escribió: Hi!

Could you put the prices of the options? And also the price of the goopy apex seal for ported engine?

Thanks!


Naj,


The half bridge and full bridge include the price for the Goopy seals for the other engines its a £125 supplement.

Other Options:

Spark Plugs = £79.99
Engine Painting £100 (one colour)
Refurbished housings = £300
Engine balancing £250
Rotor lightening £150 (can only be done with engine balancing)
Lightweight Flywheels =£369.99
Clutches = £280 (Exedy OEM Clutch)
Please Like and follow us on Facebook. http://www.facebook.com/ryanrotaryperformance

Website: http://www.RyanRotaryPerformance.com
Email: Sales@RyanRotaryPerformance.com
Contact: Carl Ryan 

Responder
#4
Thanks Carl!
Responder
#5
(18-08-2017, 10:55 AM)Ryan Rotary Performance escribió: Lots of new options now on our new website:

All engine modifications can be seen here: https://www.ryanrotaryperformance.com/rx8-modifications

One to note is that we are the first in the UK to offer re-nitrided plates for engine, if this is done along side Rotor housing refurbishment your engine will be as good as new! 
Please Like and follow us on Facebook. http://www.facebook.com/ryanrotaryperformance

Website: http://www.RyanRotaryPerformance.com
Email: Sales@RyanRotaryPerformance.com
Contact: Carl Ryan 

Responder
#6
Hola. Aunque ya estuve contando en un post como ha sido mi experiencia con el Rebuild de Chambers, creo que lo suyo es ponerlo en su propio subforo. Además hay gente que está planteándose el Rebuild y les vendrá bien.

Le pedí un street port Rebuild, con el bloque motor (sin enviar el mío), pintado de negro, y me recomendó que pidiera un servicio que hacen de renovación de los housing. Alisan la cara interna para dejarla plana y hace  que funcione mejor el rotor y sellos al ser lisa la superficie, mejorando la compresión.

Se nota que son especialistas en esto, saben muchísimo lo que hacen, y me ha contestado sin problemas los montones de correos que le puesto preguntando cosas. El contacto es súper fácil por escrito ya que con mi nivel de inglés...

Me dieron un plazo de 6 semanas que se cumplieron sin retrasos y el motor venía con cárter, cableado, termostato e inyectores, y súper bien envuelto. Se notaba todo muy cuidado y muy profesional.

El motor de ryan  va de maravilla. Arranca al toque, tanto en frío como en caliente, y suena completamente distinto al viejo. Suena redondo y va fino fino, y ahora con más kilómetros que ya le subo más de vueltas parece que anda bastante más que antes, aunque no sé si será por el porting o por el propio motor nuevo, y suena que  da  gusto oírlo. 

No ha bajado nada el nivel de aceite, ni ha tenido perdida de ningún líquido. Y también he notado una bajada importante en el consumo. 

Yo desde luego puedo recomendarles porque me parecen unos auténticos profesionales que saben lo que hacen y súper serios, y el resultado hasta la fecha ha sido excelente en mi caso.

Saludos!
Responder
#7
Bueno por lo menos parece que por fin hemos encontrado un sitio fiable para rebuilds!


Enviado desde mi iPhone utilizando Tapatalk
Responder


Salto de foro:


Usuarios navegando en este tema: 1 invitado(s)